SWITCH SEMIGESTIONABLE D-LINK STACKABLE DGS-1510-52XMP 48P GIGA POE (370W)+ 4P 10G SFP+ POE (370W)

1.360,71 Iva Incluido

SWITCHING

Agotado

SKU: DLINK DGS-1510-52XMP Categorías: , , Etiquetas: , , Marca:

Descripción

General
Port Standards & Functions
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
802.3ae 10 GbE
IEEE 802.3x Flow Control for Full-Duplex Mode
Auto-negotiation
Number of Ports
DGS-1510-20 – 16 10/100/1000 Mbps, 2 Gigabit SFP, 2 10G SFP+
DGS-1510-28 – 24 10/100/1000 Mbps, 2 Gigabit SFP, 2 10G SFP+
DGS-1510-28X – 24 10/100/1000 Mbps, 4 10G SFP+
DGS-1510-28P – 24 10/100/1000 Mbps PoE capable, 2 Gigabit SFP, 2 10G SFP+
DGS-1510-28XMP – 24 10/100/1000 Mbps PoE capable, 4 10G SFP+
DGS-1510-52X – 48 10/100/1000 Mbps, 4 10G SFP+
DGS-1510-52XMP – 48 10/100/1000 Mbps PoE capable, 4 10G SFP+
Network Cables
UTP Cat. 5, Cat. 5e (100 m max.)
EIA/TIA-568 100-ohm STP (100 m max.)
Full/Half Duplex
Full/half duplex for 10/100 Mbps and Gigabit speed
Media Interface Exchange
Auto or configurable MDI/MDIX
Performance
Switching Capacity
DGS-1510-20 – 76 Gbps
DGS-1510-28 – 92 Gbps
DGS-1510-28X – 128 Gbps
DGS-1510-28P – 92 Gbps
DGS-1510-28XMP – 128 Gbps
DGS-1510-52X – 176 Gbps
DGS-1510-52XMP – 176 Gbps
Transmission Method
Store-and-forward
MAC Address Table
16,000 entries per device
MAC Address Update
Up to 512 static MAC entries
Enable/disable auto-learning of MAC addresses
Maximum 64 bytes Packet Forwarding Rate
DGS-1510-20 – 56.54 Mpps
DGS-1510-28 – 68.45 Mpps
DGS-1510-28X – 95.24 Mpps
DGS-1510-28P – 68.45 Mpps
DGS-1510-28XMP – 95.24 Mpps
DGS-1510-52X – 130.95 Mpps
DGS-1510-52XMP – 130.95 Mpps
Packet Buffer Memory
DGS-1510-20/28/28X/28P/28XMP – 1.5 MB per device
DGS-1510-52X/52XMP – 3 MB per device
PoE (DGS-1510-28P, DGS-1510-28XMP and DGS-1510-52XMP only)
PoE Standard
IEEE 802.3af, 802.3at
PoE Capable Ports
DGS-1510-28P/28XMP
Ports 1 to 24: Up to 30 W
DGS-1510-52XMP
Ports 1 to 48: Up to 30 W
PoE Power Budget
DGS-1510-28P
Max. 193 W
DGS-1510-28XMP
Max. 370 W
DGS-1510-52XMP
Max. 370 W (740 W with DPS-700 RPS redundant power supply)
Physical & Environment
AC Input
100 to 240 VAC 50/60 Hz internal universal power supply
Maximum Power Consumption
DGS-1510-20 – 20.3 W
DGS-1510-28 – 24 W
DGS-1510-28X – 22.3 W
DGS-1510-28P ? 238.7 W (PoE on), 29 W (PoE off)
DGS-1510-28XMP – 436.3 W (PoE on), 38.4 W (PoE off)
DGS-1510-52X – 44.2 W
DGS-1510-52XMP – 486.9 W (PoE on)
Standby Power Consumption
DGS-1510-20 – 12.2 W
DGS-1510-28 – 15.2 W
DGS-1510-28X – 15.2 W
DGS-1510-28P -21 W
DGS-1510-28XMP – 28.3 W
DGS-1510-52X – 28.9 W
DGS-1510-52XMP – 40.1 W
Smart Fan Quantity
DGS-1510-20/28/28X ? 1
DGS-1510-28P/28XMP/52/52X ? 2
DGS-1510-52XMP ? 4
Acoustics
DGS-1510-20 – 43.8 dB(A)
DGS-1510-28 – 43.8 dB(A)
DGS-1510-28X – 42.7 dB(A)
DGS-1510-28P ? 46.4 dB(A)
DGS-1510-28XMP – 56.9 dB(A)
DGS-1510-52X – 45.8 dB(A)
DGS-1510-52XMP – 55.4 dB(A)
Heat Dissipation
DGS-1510-20 – 41.602 BTU/hr
DGS-1510-28 – 72.292 BTU/hr
DGS-1510-28X – 76.043BTU/hr
DGS-1510-28P ? 813.967 BTU/hr
DGS-1510-28XMP – 1487.78 BTU/hr
DGS-1510-52X – 138.787 BTU/hr
DGS-1510-52XMP – BTU/hr
Operation Temperature
-5 to 50 °C (23 to 122 °F)
Storage Temperature
-20 to 70°C (-4 to 158 °F)
Operation Humidity
0% to 95% non-condensing
Storage Humidity
0% to 95% non-condensing
Dimensions
DGS-1510-20 – 280 x 180 x 44 mm (11 x 7.09 x 1.73 inches)
DGS-1510-28 – 440 x 210 x 44 mm (17.36 x 8.26 x 1.73 inches)
DGS-1510-28X – 440 x 210 x 44 mm (17.36 x 8.26 x 1.73 inches)
DGS-1510-28P – 440 x 250 x 44 mm (17.36 x 9.84 x 1.73 inches)
DGS-1510-28XMP – 440 x 308 x 44 mm (17.36 x 12.12 x 1.73 inches)
DGS-1510-52X – 440 x 250 x 44 mm (17.36 x 9.84 x 1.73 inches)
DGS-1510-52XMP – 440 x 308 x 44 mm (17.36 x 12.12 x 1.73 inches)
Weight
DGS-1510-20 – 1.24 kg
DGS-1510-28 – 2.00 kg
DGS-1510-28X – 2.00 kg
DGS-1510-28P ? 2.54 kg
DGS-1510-28XMP – 4.25 kg
DGS-1510-52X – 2.40 kg
DGS-1510-52XMP – 5.41 kg
Diagnostic LEDs
Power/Stacking ID/Fan (per device)
Power/Stacking ID/Fan Error/PoE Push Button (per device) (for DGS-1210-28P only)
Link/Activity/Speed (per 10/100/1000 Mbps port)
Link/Activity/Speed/PoE Mode (per 10/100/1000 Mbps port) (for DGS-1210-28P only)
Link/Activity/Speed (per Gigabit SFP port)
Link/Activity/Speed (per 10G SFP+ port)
Certifications
CE
FCC
C-Tick
VCCI
BSMI
Safety
cUL
CB
Software Features
Stackability
Virtual Stacking Support
D-Link Single IP Management
Up to 32 devices per virtual stack
Up to 20G stacking bandwidth
Physical Stacking1
Supports Duplex Chain/Ring topology
Up to 40G stacking bandwidth full duplex
Up to 6 units per stack
L2 Features
MAC Address Table: Up to 16,384
Flow Control
802.3x Flow Control
HOL Blocking Prevention
Jumbo Frame up to 9,216 Bytes
IGMP Snooping
IGMP v1/v2 Snooping
IGMP v3 awareness
Supports 512 IGMP groups
Supports 128 static multicast addresses
IGMP per VLAN
Supports IGMP Snooping Querier
Host-based IGMP Snooping Fast Leave
MLD Snooping
Supports MLD v1/v2 awareness
Supports 512 groups
Supports 128 Static Multicast Addresses
Per VLAN MLD Snooping
Host-based MLD Fast Leave
MLD Snooping Querier
Spanning Tree Protocol
802.1D STP
802.1w RSTP
802.1s MSTP
Loopback Detection v4.07
802.3ad Link Aggregation
Max. 32 groups per device/8 ports per group
Port Mirroring
Support 4 mirroring groups
One-to-One, Many-to-One
Supports Mirroring for Tx/Rx/Both
Multicast Filtering
Forwards all unregistered groups
Filters all unregistered groups
Ethernet Ring Protection Switching (ERPS)
VLAN
802.1Q Tagged VLAN
4K VLAN Groups
Configurable VID: 0~4094
GVRP
Asymmetric VLAN
Auto Voice VLAN
Auto Surveillance VLAN 2.1
MAC-based VLAN
Protocol-based VLAN
Quality of Service (QoS)
CoS based on
802.1p priority
VLAN
MAC address
Ether type
IP address
DSCP
Protocol type
TCP/UDP port number
DSCP of IPv6 Traffic Class
IPv6 flow label
802.1p Quality of Service
Queue Handling
Strict Priority Queue (SPQ)
Weighted Round Robin (WRR)
Deficit Round Robin (DRR)
SPQ + WRR
8 queues per port
Bandwidth Control
Port-based (Ingress/Egress, min. granularity for 10/100/1000 BASE-T ports is 64 Kb/s)
L3Features
ARP
256 Static ARP
Supports Gratuitous ARP
IPv6 Neighbour Discovery (ND)
16 IP interfaces
Default Routing
Static Routing
64 IPv4 Static Route Entries
32 IPv6 Static Route Entries
UDP helper
Access Control List (ACL)
ACL based on
802.1p priority
VLAN
MAC address
Ether type
IP address
DSCP
Protocol type
TCP/UDP port number
DSCP of IPv6 Traffic Class
IPv6 flow label
ACL Actions
Permit
Deny
Max. 256 access list
Max. 768 rules
Single or multiple ports (each rule)
Time-based ACL
ACL Statistics
Security
Port Security
Supports up to 128 MAC addresses per port
Broadcast/Multicast/Unicast Storm Control
Dynamic ARP Inspection
D-Link Safeguard Engine
DHCP Server Screening
ARP Spoofing Prevention
Max. 64 entries
SSH
Supports v2
Supports IPv4/IPv6
BPDU Attack Protection
DoS Attack Prevention
SSL
Supports v1/v2/v3
Supports IPv4/IPv6
Traffic Segmentation
IP-MAC-Port Binding
DHCP snooping
IP Source Guard
Dynamic ARP Inspection
IPv6 DHCP Guard
IPv6 RA Guard
IPv6 Snooping
IPv6 Source Guard
IPv6 ND Inspection
AAA
Compound Authentication
802.1X Port and MAC-based Authentication
Supports RADIUS and Local Server
Supports EAP, OTP, TLS, TTLS, PEAP
Web-based Access Control (WAC)
Port-based Access Control
Host-based Access Control
Dynamic VLAN Assignment
Guest VLAN
RADIUS and TACACS+ authentication for switch access
RADIUS and TACACS+ accounting
MAC-based Access Control (MAC)
Port-based Access Control
Host-based Access Control
Dynamic VLAN Assignment
Japan Web-based Access Control (JWAC)
Port-based Access Control
Host-based Access Control
Dynamic VLAN Assignment
OAM
Cable Diagnostics
sFlow
Factory Reset
Management
Command Line Interface (CLI)
Telnet Server
TFTP Client
IPv6 Neighbor Discovery
Configurable MDI/MDIX
SNMP
Supports v1, v2c, v3
SNMP Trap
System Log
Max. 10,000 log entries
Debug command
Dual images
Surveillance mode
DHCP Client
D-Link Network Assistant support
SNTP
ICMPv6
IPv4/v6 Dual Stack
DHCP Auto Configuration
RMON v1
LLDP, LLDP-MED
DHCP relay
Web-based GUI
TFTP Client
NTP
Telnet client (supports CLI only)
D-Link Green 3.0 Technology
Power Saving by:
Link Status
LED or Port Shutoff
System Hibernation mode
Time-based PoE (PoE models only)
Optional 10G SFP+ Transceivers
DEM-431XT – 10GBASE-SR SFP+ transceiver (w/o DDM), 80 m: OM1 & OM2 MMF, 300 m: OM3 MMF
DEM-432XT – 10GBASE-LR SFP+ transceiver (w/o DDM), 10 km
Optional 1G SFP Transceivers
DEM-310GT – 1000BASE-LX SFP transceiver, single-mode fiber, 10 km, 3.3 V operating voltage
DEM-311GT – 1000BASE-SX SFP transceiver, multi-mode fiber, 550 m, 3.3 V operating voltage
DEM-312GT2 – 1000BASE-SX SFP transceiver multi-mode fiber, 2 km, 3.3 V operating voltage
Optional 10G SFP+ Direct Attach Cables
DEM-CB100S – 10G SFP+ to SFP+ 1 m Direct Attach Cable
DEM-CB300S – 10G SFP+ to SFP+ 3 m Direct Attach Cable
Optional Redundant Power Supplies
DPS-700 – AC Redundant Power Supply for DGS-1510-52XMP
1 When stacking in a linear typology, the remaining unused SFP+ ports in the stacking port pair of the top and bottom switches will also be considered occupied by the switch and cannot be used for any other purpose.

Valoraciones

No hay valoraciones aún.

Sé el primero en valorar “SWITCH SEMIGESTIONABLE D-LINK STACKABLE DGS-1510-52XMP 48P GIGA POE (370W)+ 4P 10G SFP+ POE (370W)”

Related Products

100% Garantía
Si tienes algún problema, lo solucionamos de inmediato.
24X7
Feliz de ayudarte 24X7, whatsapp Edu Diaz 620984325
Nuestra promesa
Cumplir siempre con tus expectativas